要把安裝過程和土建工程作為一個整體來對待，在安裝過程中，地面鋪設彩條布，重物和工具放在自制木板上，同時注意保護廠房的墻面、頂板、門窗及油漆、裝飾等防止碰壞。

1、絕緣瓷件、夾持件應妥善保管，輕拿輕放、防止碰傷，已安裝好的瓷件不應承受其他應力，以防損傷。

2、已調平直的母線，不得亂放，不得在母線上放置重物。

3、封閉、插接式母線及其夾持件在裝卸、運輸過程中，昭通鋁合金母線槽，應注意輕拿輕放，不得隨意在地上拖拉，不得隨意拆除包裝物。臨時堆放時，應擺放整齊，并有防塵、防水措施，不得在母線上放置建筑材料，鋁合金母線槽廠家，不得在母線上作業。如有其它工種作業應對封閉插接母線加保護，以免損傷

根據安裝方式的不同，選擇母線槽時也應注意：母線槽水平安裝，且支架能根據需要設置時，宜采用長度為3m左右的母線槽。當支架間距為6m及以上時，應選用超長型母線槽。當母線槽在不同形狀的建筑中沿平面安裝時，宜選用外殼為矩形的母線槽。當沿圓弧面安裝時，宜選用樹脂澆注母線槽或圓筒形母線槽。當母線槽垂直安裝時，宜選用密集絕緣或樹脂澆注母線槽，且絕緣材料應采用適用于長期工作溫度不低于130℃的材料。為避免煙囪效應，當選用空氣絕緣母線槽時，鋁合金母線槽價格，母線槽殼體內每單元間應設置阻火隔斷。

密集母線槽可為交流三相三線、三相四線和三相五線制，頻率為50-60Hz，電壓至400V，額定工作電流為250~5000A，主要用作工礦、企事業和高層建筑中新型的供配電設備。帶插口的母線槽，可通過插接頭箱或開關箱，便能方便地引出電源分路。由于母線槽具備體積小、結構緊湊、傳輸電流大、維護方便等優點，成了市場“搶手貨”。  它的安裝可直接從變壓器接到低壓配電柜，也可從低壓柜直接接到配電系統作為配電干線線路。

、母線通道水平安裝，兩支架間距≯2500㎜，垂直安裝間距≯3600㎜。  2、垂直安裝時，安裝支架應與通道側板配鉆孔，采用M6-M8螺栓緊固。  3、安裝施工工藝，應優先采用從饋送電系統，由母干線至分支干線的施工方案。  4、封閉式母線通道安裝基本順序：選定布線方向→固定支架→槽間用四枚螺栓緊固→相間加入母線接頭板和絕緣墊→單頭螺栓穿入絕緣套管→螺栓穿入母排予置孔→兩端緊固→加半裝上下蓋板→將通道固定在支架上。