不銹鋼潛水推流器安裝注意事項：

   a、安裝底座、支座及導桿時應校正水平度（要求水平度為0.2mm/m），推流器，以保證導桿的鉛垂度。

   b、在裝配起吊架時應在與支座孔配合的軸頸表面涂抹油脂。

   c、在起吊攪拌機時，應先選擇攪拌機吊梁上合適的起吊孔位置，保證葉輪端上仰約3°~10°；再調整手拉葫蘆掛鉤在起吊架橫梁上起吊孔的位置并旋轉起吊架，直到攪拌機安裝至導桿后，起吊環鏈中心線與導桿中心線應基本平行(這里可通過目測及尺測的方法測試。當攪拌機沿導桿下滑接近限位架，起吊環鏈處于拉緊狀態時，目測起吊環鏈中心線與導桿中心線是否在同一鉛垂面上；用直尺測量導桿上端至吊環鏈的垂直距離及導桿下端至吊環鏈的垂直距離，誤差應小于10mm)，并保證攪拌機沿導桿緩緩下滑或吊起時無卡阻現象。

   d、在起吊攪拌機時，低速潛水推流器廠商，起吊環鏈不得纏繞，手拉葫蘆手拉鏈槽須正對起吊人。

   e、電纜的固定位置應適度，既不能過緊受力而損壞電纜，又不能過松造成電纜卷入葉輪中而損壞。電纜夾與電纜間配有橡膠保護套，電纜裝夾后，應保證電纜不得松脫。當電纜裝夾出現夾不緊時，應在電纜外包箍膠帶后再裝電纜夾，潛水推流器廠商，以保證電纜不會松脫。

 潛水推流器系統軟件自動式運作，不用人工服務值班，系統軟件關鍵由潛水推流器、太陽能發電列陣、離心水泵構成。系統軟件省去掉電瓶這類的儲能技術設備，以儲水取代蓄電池，立即驅動器離心水泵揚水。潛水推流器系統對的運作執行操縱和調整，高速潛水推流器廠家，保持至大功率點跟蹤。當光照充裕時保證系統額定值運作，當光照不夠時，設置少運作頻率考慮，保證太陽電池電力工程的充足運用。

    太陽電池列陣由幾塊太陽電池部件串并聯而成，消化吸收光照輻射源動能，將其變換為電磁能，為全部系統軟件出示驅動力開關電源。