防盜井蓋安裝裝配式檢查井由各預制配件組合構成，施工時采用吊機由下至上，逐一吊裝各預制配件，混凝土配件的裝嵌要嚴格按照設計要求施工。各預制件吊裝前應檢查，檢查井井筒批發，確保其表面平整、光滑、無蜂窩麻面，接口處平整光滑無崩角、崩邊、漏筋。每段預制井構件設計有4 個裝配吊環，對稱分布在構件外壁四周，檢查井井筒生產，因井壁較薄（壁厚16cm），起吊時起吊角必須大于60°，防止出現過大的水平應力造成構件受損。

預制檢查井鋼模具土方采用機械開挖，專人進行標高復核，防止土方超挖。土方開挖至檢查井鋼模具底部高程以上20cm～30mm 后采用人工清底。預制檢查井模具施工時，根據井深不同，檢查井井筒廠價，確定不同的地基施工承載力要求，同時滿足設計要求。經檢驗，地基承載力達到設計即可墊層施工。預制檢查井模具墊層采用C15 混凝土墊層，墊層下再鋪設3∶7 灰土。

預制檢查井模具井筒安裝注意事項1.檢查井模具施工前將檢查井井口50cm范圍內清理干凈、復核施工范圍尺寸及高程;根據墊層圈的位置及檢查井模具井室預留井口位置進行井筒安裝，安排工人配合，使節預制檢查井模具井筒的踏步與井室內預埋踏步的在同一方向;吊裝第二節檢查井模具井筒時，應慢慢套入節井筒中，沾益檢查井井筒，并調整預制井筒，避免磕碰，確保踏步與上一節方向一致，如此施工直至安裝完畢。