連接箱盤面板上的電器及控制臺等可動部位的電線應采用多股銅芯線并留有余量，抽屜式配電柜，線束外套塑料管加強絕緣，成束綁扎，不同電壓等級，不同控制回路應分別綁扎，標識明確，有動力機械的要落實明白設計的動力控制開關的型號及品牌，是雙速還是單速控制。箱里面的設計電線必須符合要求，線徑，顏色（與設計A/B/C的相數及顏色相符）。寬度300mm及其以上的配電箱，其頂部要設置過梁。動力箱二次線歸順整齊，帶電箱蓋跨接良好，應在其配電線路的末一級配電箱處設置自動切換裝置。

浪涌保護器接地端應與配電箱保護接地線接地端子板連接，配電箱接地端子板應與所處防雷區的等電位接地端子板連接；帶有接線端子的電源線路浪涌保護器應采用壓接；高壓系統的布線和交接試驗，必須符合GB50150規定。接地或接零支線必須單獨與相應的干線連接，不允許串聯連接。箱子鐵皮厚度要求為1。5mm，戶表箱可以1。2mm，大箱及落地柜要適當加厚。配電箱是按電氣接線要求將開關設備、測量儀表、保護電器和輔助設備組裝在封閉或半封閉金屬柜中或屏幅上，構成低壓配電裝置。正常運行時可借助手動或自動開關接通或分斷電路。

配電柜在停電時需注意事項：關于其停送電操作規則。送電原則是需要我們按照先合刀閘、后合負荷開關，先合高壓開關，后合低壓開關，先合電源側刀閘，后合負荷側刀閘，先合電源側開關，后合負荷側開關的原則進行。這其中每一步與每一步之間的順序都不能弄混，以免造成我們在使用時引發其它故障。停電順序，與上述操作原則相反。