安全性能：防相間短路，密集型母線槽為防止出現相間短路，母線不準有毛刺、加工時不準有垃圾混入殼體內、加厚絕緣層，但不能完全防止短路出現的可能性！但是防水型母線槽是采用的絕緣樹脂將母排直接澆注密封，防護等級達到IP68！所以防水型母線槽幾乎不存在短路的可能！機械性能：能承受6焦耳的機械沖擊，低壓密集型母線槽，確保使用安全，具有良好的防爆性能。

母線槽一般應用的行業有：專門的安裝公司，新建的廠房等建筑，蚌埠密集型母線槽，使縫隙更為狹窄，因此兩段母線槽主母排連接時，兩段母線軸線要嚴格保持在一條中心線上，此目的是為防止螺栓上的絕緣套管在安裝過程中避免受到剪切力的作用而導致損傷。按規范要求，為滿足母線的搭接面積，密集型母線槽安裝，螺栓孔與螺栓之間縫隙較小，由于母線槽螺栓增加了絕緣套管，10kv密集型封閉母線槽，并使兩段母線槽的母排及絕緣板的螺栓孔完全對齊，穿上螺栓上緊時，每個螺栓要依次用力均勻。

將母線連接到電纜分箱，再由電纜分支箱向每個樓層供電，把母線當插座使用，沒有體現出母線的優勢，不建議采用這樣的供電方式。雙母接線的母線發生故障，在處理故障過程中要注意母線保護的運行方式，必要時應短時停運母線保護。因此兩段母線槽主母排連接時，兩段母線軸線要嚴格保持在一條中心線上，并使兩段母線槽的母排及絕緣板的螺栓孔完全對齊，穿上螺栓上緊時，每個螺栓要依次用力均勻。