現在溶出儀一般為全自動或半自動取樣，在自動取樣溶出儀的取樣端，通用型8杯溶出儀多少錢，一定要安裝濾頭，若不在取樣針的取樣端安裝濾頭，未溶解的樣品顆粒會隨取樣溶液進入儀器管路，通用型8杯溶出儀， 一方面，通用型8杯溶出儀價格，未溶解的顆粒可能堵塞管路，使儀器取樣量不準確；另一方面，因為樣品從取樣端轉移到試管的時間（根據取樣量不同）一般會有2-5min的間隔，未溶解的顆粒在管路中轉移時也會繼續溶解，因此會影響測量的準確度或終溶出度。 試驗結束后，使用過的濾頭應在溶媒中超聲20-30min后，再用純化水超聲清洗，不能僅用溶出介質浸泡后，用清水沖洗。因為這種方式不能將濾頭清洗干凈，會影響下次使用。

溶出杯與攪拌槳（籃）一樣有不同的編號。使用時也應將溶出杯安裝到對應的位置。除了溶出杯的編號要對應外，溶出儀通過了垂直度與同軸度驗證后，溶出杯上緣與固定裝置相連的位置上都做好標記。如：豎線、箭頭。 因此，在進行溶出度試驗時，應將各籃軸、槳和溶出杯放在原已通過驗證的位置上，保持各溶出杯與固定裝置的相對位置不變。但是大家在安裝溶出儀時往往會忽略這點，使的溶出杯的軸度與攪拌槳的軸度不重合，通用型8杯溶出儀哪家好，進而改變溶出杯內溶出介質的流動狀態，使溶出數據發生變化。

在溶出杯的水平面板上從兩個垂直方向上測量，兩次測量的數值均不得超出0.5°。

　將需驗證的溶出儀放置在一水平且平穩工作臺上，工作臺所處環境不允許有振動。調節溶出儀底腳，使溶出儀杯板在前后、左右兩個方向上均能接近水平。在后續的驗證及驗證后的試驗過程中不能調整或移動溶出儀，否則需要對溶出儀進行重新驗證。技術要求：緊貼籃（槳）軸測量垂直度，再沿籃（槳）軸旋轉90°測量，每根籃（槳）軸兩次測量的數值均不得超出90.0°±0.5°。