不能將線纜捆扎在一塊

一般來說，電源濾波器廠家，在電子設備或系統內安裝電源濾波器時要注意的是，在捆扎設備電纜時，千萬不能把濾波器（電源）端和（負載）端的電線捆扎在一起，三相電源濾波器，因為這無疑加劇了濾波器輸入輸出端之間的電磁耦合，嚴重破壞了濾波器和設備屏蔽對EMI 信號的抑制能力。

電源濾波器輸入線、輸出線

必須拉開距離電源濾波器輸入線、輸出線必須拉開距離，切忌并行，以免降低濾波器效能。

電源流過的電流主要是共模的，但上面噪聲也可能會以差模的形式出現，若要抑制差模噪聲，開關電源濾波器，需要另外使用差模電感，或是各相有個別的電感器。在電源濾波器上會使用特別的安規解耦電容，分為X電容及Y電容二類：X電容：抑制差模干擾（電源線之間的干擾）。Y電容：抑制共模干擾（各組電源線對地之間的干擾）。由于Y電容提高會使電器的漏電流增加，而電器的漏電流有其規定范圍，因此Y電容不能太大，一般都會比X電容要小。

結構特性：

DL系列單相電源濾波器采用全密封結構，具有良好的防潮性能和屏蔽性能。外殼底面無漆層，依靠安裝螺釘，將濾波器緊壓在設備架或機箱板上，湖州電源濾波器，以保護良好的電接觸。

使用方法：

1.濾波器上標志（Line）一端的應接電網，（Load）一端應接至負載（設備和儀器）。

2.DL-□AZ型為帶插頭型電源濾波器，有插頭一端應插入220V電源。

3.濾波器的安裝尺寸