防爆電機停轉、接通電源后又不轉，YBZJ防爆倉壁振動器生產廠家，過會時間又可以啟動

可能原因：

1.繞組短路

2.過載

3.熱保護器動作

處理方法：

1.修理繞組

2.檢查傳動部分及工作機械，排除故障

3.過熱或過電流后熱保護器動作，冷卻后又復位

防爆電機異常振動

可能原因：

1.軸頭彎曲

2.底腳松動

3.轉子動平衡破壞

4.電路、繞組故障

處理方法：

1.校直

2.固定底腳

3.校正動平衡

4.檢查、修理電路或繞組

礦用防爆電機發展大功率電機：目前世界上采煤機的大裝機容量已超過1200kw，其驅動電機功率達600kW；相適應的采區工作面刮板輸送機的大裝機容量已超過1500kW，YBZJ防爆倉壁振動器生產廠家，其驅動電機功率已達725kW。國內目前的采煤機驅動電機大功率是400kW，西藏防爆倉壁振動器生產廠家，刮板輸送機驅動電機大功率是315kW。發展3.3kV、6kV和10kV級電壓的礦用電機：這是因為普及綜合機械化采煤機組后采區走向加長，導致電壓降增大，同時大功率電機的使用也要求提高電壓等級。

防爆電機外殼帶電

可能原因：

1.接地線松動或斷開

2.繞組絕緣受損、或受潮，引出線碰殼

處理方法：

1.檢查接地線，接好

2.烘干，YBZJ防爆倉壁振動器生產廠家，修理絕緣及更換引出線

防爆電機運轉中聲響異常

可能原因：

1.缺相運行

2.轉子或轉子上夾帶異物與定子或其它固定物相擦

3.軸承損壞或嚴重缺油

4.波行墊圈斷裂

5.離心開關損壞

6.軸向竄動太大

處理方法：

1.檢查電路各元件，排除故障

2.檢查定子內膛及轉子有無凸出異物，軸承室是否磨損太大

3.清洗軸承、加腐滑脂

4.更換波形墊圈

5.修理或更換離心開關

6.調整軸向竄動量