液壓油冷卻循環系統工作不良通常，采用水冷式或風冷式油冷卻器對液壓系統的油溫進行強制性降溫。水冷式冷卻器，會因散熱片太臟或水循環不暢而使其散熱系數降低；風冷式冷卻器，會因油污過多而將冷卻器的散熱片縫隙堵塞，風扇難以對其散熱，結果導致油溫升高。預防措施：定期檢查和維護液壓油冷卻循環系統，液壓油多少錢一升，一旦發現故障，必須立即停機排除。

油溫升高的主要原因1、首先是工作環境溫度過高，通風條件太差，造成油溫極易升高。所以應盡量避開高溫時間點作業。如果條件允許，請在液壓系統回油管路，加裝風冷式液壓油散熱器，對液壓系統進行物理降溫。2、液壓油箱太小或者油位太低，液壓油沒有足夠的循環條件及冷卻條件。液壓油工作過程中，主要通過液壓油箱散熱。油箱面積越大，越利于散熱。

在工作條件惡(e)劣的場合，為保證系統的，要選用粘溫特性、熱穩定性、潤滑性以及防銹蝕等性能好的油液。3、根據密封材料選擇。液壓裝置的密封件材質與系統所使用的油液相容，32號液壓油價格，否則密封件在會出現膨脹、收縮、侵蝕、溶解等現象，蕪湖液壓油，造成系統性能下降，如HM抗磨液壓油與天然橡膠、丁基橡膠、乙烯橡膠、硅橡膠等相容性較差，這點在實際使用當中是要予以重視的。