數控加工切削用量的確定：(1)主軸轉速n(r/min)：1主軸轉速一般根據切削速度來選定。計算公式為：n=1000/d，式中d為刀具直徑(mm)。數控機床的控制面板上一般配有主軸轉速修調(倍率)開關，可在加工過程中對主軸轉速進行倍率調整。(2)進給速度F：進給速度應根據零件的加工精度和表面粗糙度要求以及刀具和工件材料來選擇。

cnc數控加工工序的安排：1、內外1交叉原則對既有內表面（內型腔）又有外表面需要加工的零件，安排加工順序時，銅陵數控加工，應行內外表面粗加工，后進行內外表面精加工。切不可將零件上一部分表面（外表面或內表面）加工完畢后，再加工其他表面（內表面或外表面）。2、基面先1行原則應優先加工用作精基準的表面。這是因為定位基準的表面越精1確，裝夾誤差就越小。

產品的進度要求越來越嚴格，后續就要進行半精加工和精加工階段。3、先面后孔：在進行機械加工的時候，數控加工廠，對于支架這樣的工件來說，制動器它既要進行平面加工又要機械孔加工，為了加工出來的孔的精度誤差更小一些，先加工平面后加工孔有利于減小誤差。4、光整加工：這個加工原則大致就是一些打磨拋光的加工，它通常是在產品全部完成架構之后進行的步驟。