目前市場上光纖熔接機主要分為：單芯光纖熔接機、帶狀光纖熔接機和保偏光纖熔接機三種。我們平時常用到的光纖熔接機，基本上都屬于單芯光纖熔接機。帶狀光纖熔接機主要用于帶狀光纜的熔接，藤倉光纖熔接機維修費用，一次可以熔接8芯、12芯，一般用在城市的主干傳輸線路上。保偏光纖熔接機主要用于保偏特種光纜，這種用量非常少。

光纖熔接機熔前是根據光纖的材料和類型，設置好預熔電流和時間以及光纖送入量等關鍵參數。熔接過程中還應及時清潔熔接機“V”形槽、電極、物鏡、熔接室等，隨時觀察熔接中有無氣泡、過細、過粗、虛熔、分離等不良現象，注意OTDR測試儀表跟蹤監測結果，及時分析產生上述不良現象的原因，采取相應的改進措施。

了解光纖熔接機，首先，要了解光纖熔接機的分類有哪幾種。然后，藤倉40s光纖熔接機維修視頻，再根據自己的工程，去選購對應類型的光纖熔接機。

清理光纖壓腳

如果光纖壓腳上有臟物，光纖就不能正常夾住，從而降低熔接質量。在正常的操作過程中，藤倉光纖熔接機維修價格，應經常檢查和定期清理光纖壓腳。

（l）將防風罩打開，可以看到在防風罩內側的光纖壓腳。

（2）使用蘸酒精的棉棒清理光纖壓腳的表面如圖5-3中所示，用干的棉棒清除多余的酒精。

檢查：使用純度超過99%的高質量酒精

用圖象處理技術以識別有時在熔接過程中發生的異常狀況。有時，一個很小的毛病未檢測到可能造成不好的熔接質量。在熔接過程的各個階段，通過顯示屏可觀察光纖圖象，并確認是可接受的或不可接受的狀態。

(1)開始熔接

按＜＞鍵開始自動熔接程序，光纖熔接機，程序將自動向前移動左右光纖。在完成電弧清潔放電后，光纖將停止在預先設定的位置。

a注：當光纖向前移動并且出現上下跳動時，可能是V型槽或光纖表面被污染。清潔V型槽并重新制備光纖。

(2)切割角度測量和纖芯對準操作

當熔接機正在運行或暫停時，可以通過肉眼觀察光纖端面的情況。

a檢查：即使沒有切割角度的錯誤信息提示，發生以下情況時，也應按<>并重新制備光纖。