高壓反應釜釜體材料主要采用 1cr18Ni10Ti 不銹鋼制作，并可根據不同介質要求制作鈦材（ TA2 ）、鎳（ Ni6 ）及復合鋼板，釜體結構有平蓋、凸形蓋以及帶人孔的閉式反應釜體，釜蓋上的開孔可根據用戶要求進行設計；加熱方式有夾套蒸氣、夾套熱油電加熱等形式供用戶訂貨時任意選配。 對有拋光要求的釜體內表面，可達到 以上的鏡面拋光水平，對高粘度的物料加工成錐形底，便于放料、清洗。反應釜清洗要求：1、將反應溶劑從排氣閥充入釜內，清洗掉大部份殘留物后，注入水半釜進行攪拌10分鐘，此時方可打開釜蓋，對釜內壁進行清洗。2、清洗時，必須清洗釜蓋、取樣閥，同時在釜內有水的情況下，稍充一下氮氣。3、暫時不用的反應釜，好將反應釜內加入70%體積干凈的無水乙醇浸泡，可以不擰緊螺絲。高壓釜清洗完后，方可方便下次使用。使用實驗室高壓反應釜有哪些注意事項:水壓試驗后，再可進密試驗。1．氣密試驗壓力為我作壓力。2．氣密試驗的介質為氮氣或者其它惰性氣體。3．氣密試驗時，升壓必須分次進行。達到壓力后，保壓一定時間，用肥皂水檢查有無泄漏，合格后緩緩泄壓。

反應釜清洗要求：1、將反應溶劑從排氣閥充入釜內，清洗掉大部份殘留物后，高壓反應釜，注入水半釜進行攪拌10分鐘，此時方可打開釜蓋，實驗室高壓反應釜多少錢，對釜內壁進行清洗。2、清洗時，必須清洗釜蓋、取樣閥，同時在釜內有水的情況下，稍充一下氮氣。3、暫時不用的反應釜，將反應釜內加入70%體積干凈的無水乙醇浸泡，可以不擰緊螺絲。高壓釜清洗完后，方可方便下次使用。高壓發應釜適用范圍，高壓釜即高壓反應釜，適用于大專院校實驗、石油化工、染料礦冶、納米材料、聚合物反應、水熱合成、氫化反應、科技、食品、卷煙業、陶瓷業、高分子業、精細化工、微生物工程、高新科技產品等領域智能高壓反應釜：磁力傳動裝置將真正用于攪拌的部件密封在壓力環境內，以此解決了攪拌軸與反應器之間動密封的可靠性。由于磁力傳動裝置的基本制造材料均為鐵磁性物質（鐵基合金，鎳基合金），磁導率，磁場在穿過用于密封合金層時幾乎沒有損耗。由此外部驅動永磁體產生的旋轉磁場可以有效被內部永磁體轉子接受，進而帶動反應器內的攪拌部件進行物料混合。

使用實驗室高壓反應釜有哪些注意事項:水壓試驗  1．安裝完畢后進行水壓試驗，水壓試驗按1.05倍工作壓力試驗。 2．要求裝配量程為工作壓力的1.25倍的合格壓力表 3．用清潔水作介質，確認氯離子含量不超過25毫克/升，水溫≥5°C。4．充介質時，容器頂部設排氣口，必須把容器內部的氣體排放干凈。5．試壓時，壓力應緩慢上升，注意觀察壓力指示是否變化，容器有無變形，高壓反應釜廠商，傾聽有無異常聲響，達到試驗壓力保壓30分鐘。無泄漏后，將壓力緩緩降到試驗壓力的80%；保壓一定時間，對所有的接頭和連接部位進行檢查。合格后緩緩缷壓，放盡介質，用壓縮空氣將容器內外吹干凈。注意事項：高壓反應釜要在的地點使用，并按照使用說明進行操作。查明刻于主體容器上的試驗壓力、使用壓力及使用溫度等條件，要在其容許的條件范圍內進行使用。高壓反應釜的操作及注意事項：4、氧氣壓力計應避免與其他氣體壓力計混合。5、安全閥和其他安全裝置應定期檢查符合要求的設備。6、操作時必須注意溫度計應準確插入反應溶液。7、保持高壓反應釜內部和墊片清潔。8、蓋上盤式法蘭蓋時，大型高壓反應釜，位于對角線上的螺栓應依次擰緊。9、測量儀器時，大多數情況下玻璃表面前后兩側。所以操作時不要站在這些危險的地方。當預計有危險時，卸下玻璃，換上新的。